Capabilities

Tooled, pressed and ground in our own plants

15 presses from 5 T to 100 T, an in-house tool room, specialised grinding and wire bending. Here is what each one does, the materials we work in, and the capacity we have free.

Press shop

15 presses, 5 T to 100 T

Strip goes in on coil feeders or by hand, through compound dies and progressive dies made in our own tool room.

Presses15
Press force5 T to 100 T
FeedCoil feeders, or by hand
DiesCompound dies and progressive dies, made in-house
Stock thickness0.1 to 5.0 mm
MaterialMild steel; carbon spring steel, grade EN 42J or EN 9 (C80 or C55); stainless SS 304 or SS 316
Installed capacityabout 200,000 pcs/day
Press shop: power presses along the left wall, operators at hand presses on the right, parts in blue bins.
Press shop, Mulund, Mumbai.

Tool room

Our own dies

Dies are made and maintained in our own tool room, so a drawing change does not wait on an outside toolmaker.

Equipment
Lathe, milling, drilling and wire EDM, all in-house
New die
Timeline confirmed once we have studied your drawing
Die types
Compound dies and progressive dies
Tool ownership
Photoray makes and owns the tooling
A toolmaker working on a die set at a bench vice in our tool room, with die sets on the shelves behind him.
The tool room, where we make and maintain our dies.

Grinding

± 0.005 mm on thickness

Specialised grinding machines, including a rotary grinder. Ground thickness is held to ± 0.005 mm, measured per part at four points on a comparator stand.

± 0.005 mm

Ground thickness

Measured per part at four points on a comparator stand.

Wire bending

Split pins and wire forms

Split pins and customised wire-formed parts, bent in-house.

Sizes
Any diameter and length, to your drawing
Materials
Mild steel or carbon spring steel wire, or stainless SS 304 or SS 316

Split pins Wire-formed parts

Capacity

Room to grow a part with us

Headroom is the number that matters: it tells you whether a part can grow with us without a new vendor and a new approval cycle.

200,000

Installed capacity, pcs/day

Estimated across all 15 presses.

75%

Current utilisation

Share of installed capacity in use today. The other 25% is open for new parts.

50,000

Headroom, pcs/day

Installed capacity minus current output.

Download PPAP Capacity Chart (PDF)

Materials

The steels we work in

Every part is made from 0.1 to 5.0 mm stock in one of these grades, or in the grade named on your drawing.

MaterialGradeUsed for
Carbon spring steelEN 42J (C80)Circlips, E-clips, snap rings, conical, wave and star washers, slotted dowel pins
Carbon spring steelEN 9 (C55)Washers, shims and pressed parts that need strength and some spring
Mild steelTo your drawingPlain washers, shims, split pins and pressed parts that do not need to spring back
Stainless steelSS 304Parts that must resist corrosion
Stainless steelSS 316Parts in wet, salty or chemical service

Finishes: zinc plated with yellow or green trivalent passivation, phosphating, or blackening. Other grades and finishes to your drawing.

Secondary operations

After the press

  • Heat treatment: in-house or with outside partners, depending on the volume.
  • Finishing: zinc plating with yellow or green trivalent passivation, phosphating and blackening, in-house or with outside partners, depending on the volume.
  • Deburring in-house: a vibro finisher, a tumbler and a metal polishing machine.
  • Packing: sealed on an automated sealing machine for dispatch.

Request for quotation

Send us the drawing.

We reply with a feasibility note within 2 working days for a part made to a standard, and within 5 working days for a custom part. PDF, DWG and STEP files accepted.

Or email the drawing to inquiry@photoray.co.in.